After over a 5-year hiatus from enjoying track days, I finally got the opportunity to go again in Bumblestook. Brad set up another S2K Takeover at the NY Safety Track in Jefferson, NY after the first one earlier this year went really well. I arrived there on Sunday afternoon since I'd never been to this track before and wanted to be able to get a track walk in with the guys to get some pointers.
NYST - 9-17-2018
I'm really glad I did. Despite having watched a bunch of in-car videos from other people, it wasn't until the track walk that I understood how much of an elevation change there was and how blind the corners were. It's a bit disconcerting since there's also minimal to no runoff so for this track, in particular, I'd have to be extra careful the next day.
Track walk - 9-16-2018
I got back on site the next day bright and early. I did the usual things of emptying the car out and giving her a once over to make sure I wouldn't have any issues.
Ready to run - 9-17-2018
Coincidentally, the night before during dinner with everyone, I was chatting with Billman and he happened to have exactly one of his new generation TCTs (timing chain tensioner) with him. There's nothing wrong with my old tensioner but they do eventually go bad and it is 13 years old after all (the engine in Bumblestoook is from a 2005 S2000). Billman modifies the OEM tensioner to never be a problem so as part of buying the new TCT from him, he took care of the install which he can probably do with his eyes closed. At least I don't ever have to worry about the TCT going bad on me ever.
Billman's new TCT - 9-17-2018
Billman's new TCT - 9-17-2018
Billman installing the TCT before my first session - 9-17-2018
The track is definitely intimidating despite only being a mid-speed track (topped out at around 102mph on the straight). A lot of the corners are blind and cambered and as I mentioned earlier, the lack of runoff means you really can't just "send it". Although I'd say more than a few did and they might need to do some buffing later.
Track Map - NYST
The developers of Hotlap where there as sponsors testing out some new changes to their software that allowed real-time telemetry and track position to be seen on the web or on the phone. It wasn't entirely perfect not because of the software but because a lot of us were having bad cell service up there and more important, the cloud cover wreaked havoc on our GPS units. In one instance, even my Racepak dash was confused and saying I was going 500mph.
Hotlap data on my fastest lap - 1:44:630s
Overall I'd say the track is a lot of fun but you really have to respect it or you might brown your pants. I'll probably go back again but exercising an equal amount of caution as I did today. I was hoping to get some good video using TrackAddict and the GoPro but the GPS issues caused all kinds of problems and all I was left with was the raw video. Thankfully due to the overcast, you can actually read my dash for once so at least there's that.
Final laps of final session - NYST - 9-17-2018
We all had a chance to do seven 20 minute sessions but I only did six and opted to leave early instead since I saw some big clouds rolling in. I'm glad I did because right after filling up the tank, I drove through a pretty decent rain shower all the way home. Hopefully, that did wonders cleaning up my wheels. The Carbotech XP10/XP8 combo was phenomenal and surprisingly really quite fine on the street. I'm now debating just leaving them on all the time instead of swapping back and forth with stock pads. The oil cooler is working great too. Didn't see temps go past 209F at any point during the day.
With just a little over a week left before the S2K Take Over Round 2 at NYST, I had to get cracking on getting Bumblestook track ready.
New front rotors and track pads on - 9-8-2018
Everything's been running pretty smoothly so the only real prep left were the brakes. I opted to go with Carbotech XP10 up front and Carbotech XP8 in the rear.
Track Pads - 9-8-2018
Carbotech XP10 front pads - 9-8-2018
Carbotech XP8 rear pads - 9-8-2018
They offer great brake performance for running street tires on track and I paired them up with a fresh set of Centric cryo-treated rotors.
Centric Cryo Rear Rotors - 9-8-2018
Centric Cryo Front Rotors - 9-8-2018
Rear rotors and track pads installed - 9-8-2018
To further help with brake cooling, I finally connected the bumper brake duct inlets to the brake rotor shield. This should greatly help reduce the chances of cracked rotors.
Hose connected to brake duct inlets - 9-8-2018
Brake ducts fully connected - 9-8-2018
As the last bit of safety enhancement, I also picked up an Element E50 fire extinguisher and mounted it in front of the passenger side seat. Hopefully, I never have to use this but something is better than nothing in case of an emergency.
If you haven't seen this thing in action it's pretty cool and I think I might have to get one of these for each of my cars and apartment.
About eight months went by since I ordered the Mugen Aero Bonnet. It got fabricated, then shipped from Japan and arrived here a few weeks ago but I only had time to actually put it on today. The fitment, finish, and quality is next to none. It weighs a scant 10lbs and is designed to keep engine temps down which I was able to verify on the drive back. Bumblestook has her original color scheme back. Might not be everyone's cup of tea but I love it and that's really all that matters.
Mugen Aero Bonnet - 9-2-2018
The hood was all packaged up very nicely which is nice since I was able to reuse the box to store my OEM hood for the future if I ever decide to put it back on (yea right haha).
Mugen Aero Bonnet - 9-2-2018
Mugen (left), OEM (right) - 9-2-2018
Ready for install - 9-2-2018
It was a pretty straightforward swap but I did have to raise the hood latch up in order for the hood to lock properly. I don't even know if photos do the hood justice but the dry carbon 1x1 weave is gorgeous.
Mugen 1x1 weave dry carbon - 9-2-2018
Mugen 1x1 weave dry carbon - 9-2-2018
Unlike the replicas out there, Mugen thought of everything including adding rain channels to redirect the water if it rains despite the scoops being open.
Rain channels - 9-2-2018
Vented to perfection - 9-2-2018
I was in Tokyo earlier this year and picked up a really nice model of a yellow Mugen S2000. I'd say that's pretty close now.
Big Boys Toys - 9-2-2018
Big thanks to Alex for giving me an extra set of hands to get the hood on today. We figured we'd do a quick photoshoot of our cars while we were at it.
S4 and S2000 - 9-2-2018
Bronze wheel squad - 9-2-2018
Once we get back from the track in a few weeks, she'll go back to PeeJ so the hood can get ceramic coated as well. I think I'm going to leave it unpainted at this point. The weave just looks too good to be hidden under paint.
